Two-brothers-racing Can-Am Renegade 800R / Outlander Bedienungsanleitung PDF herunterladen

V.A.L.E.

VARIABLE AXIS LOCKING EXHAUST

IMPORTANT - PLEASE READ CAREFULLY

Warranty

Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”

without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular

purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use

of these products or parts.

Installation Instructions

1. Make sure the ATV is completely cool before starting

the installation. Make sure the ATV is secure on a level

surface and the parking brake is set.

2. Remove main seat assembly.

3. Remove heat shield.

4. Loosen mufer joint clamp.

5. Remove mufer mounting bolts *The nuts on the back

are difcult to get a wrench on but it is easier than

removing the rear section.

6. Remove OEM mufer assembly and joint clamp with

gasket.

7. Install TBR supplied mufer hanger bracket in the

rearward position of OEM mufer mount and secure

with 8x50mm bolt.

8. Attach TBR slip-tube to TBR mufer using the supplied

X-ring and 8x14mm bolts and lock washers. Leave loose

for now.

9. Slide supplied barrel clamp over slip-tube at joint end.

10. Install TBR mufer assembly, attach with supplied 8x25mm

bolt and OEM nut.

11. Tighten the X-ring bolts.

12. Tighten Barrel clamp.

13. Re-install heat shield, and seat.

14. Double check your work and make sure all bolts are

tightened and the exhaust is aligned correctly.

15. Before you run the ATV, clean off all ngerprints and

dirt, as any oily residue will etch the metal and become

somewhat permanent when the system gets hot. Run the

ATV and enjoy. It is normal for some white smoke to

appear the rst time you start the ATV. This is packing/

manufacturing oil from inside the pipe burning off.

Check for gaps or leaks. If you nd a leak, a little high

temperature silicon sealant should x it. After 50 to 100

miles, recheck all fasteners for tightness.

We recommend that this performance part be installed by a qualied

motorcycle technician. If you have any doubts as to your ability to install this

performance part, please consult with your local motorcycle dealer. Read all

instructions rst before starting installation. Make sure the motorcycle and

exhaust system are completely cool before starting the installation. Be sure

to save all stock components for possible use later.

**This product has not been tested with all available accessories and some

items may cause excessive heat. Excessive heat may cause damage to your

vehicle. Two Brothers Racing will not be responsible for damaged parts.

Renegade / Outlander 800R

V.A.L.E.™ Slip-on Exhaust System with M-7 Aluminum Canister

Part # 005-2560406V

1 2

V.A.L.E 1

Inhaltsverzeichnis

Seite 1 - V.A.L.E

V.A.L.E.VARIABLE AXIS LOCKING EXHAUSTTMIMPORTANT - PLEASE READ CAREFULLYWarrantyTwo Brothers Racing products are intended for closed course competitio

Seite 2

Care & CleaningCare & CleaningKeep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before

Kommentare zu diesen Handbüchern

Keine Kommentare

Two-brothers-racing Can-Am Renegade 800R / Outlander Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Two-brothers-racing Can-Am Renegade 800R / Outlander herunter. Two Brothers Racing Can-Am Renegade 800R / Outlander User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Two-brothers-racing Can-Am Renegade 800R / Outlander